Track Gauge Explained: Standard, Broad and Narrow

Track gauge is the distance between the inner faces of the two rails a train's wheels run on. More than half of the world's railways are built to standard gauge, 1,435 mm (4 ft 8½ in), while the rest run on broader or narrower gauges chosen for cost, speed, or local history.
Standard gauge: the world's default
Track gauge decides which locomotives and wagons can run where, and whether one railway's trains can simply roll onto a neighboring line or have to stop at the border.
Standard gauge is 1,435 mm, or 4 ft 8½ in. It goes back to George Stephenson's early lines in northern England, and Britain, then most of Europe, North America and China adopted it. Why such an odd number won is a story of its own, told in why standard gauge is 4 ft 8.5 in.

The world's gauges, country by country
Indian gauge, at 1,676 mm, is the widest gauge in common use anywhere in the world. It is used in India, Pakistan, Bangladesh and Sri Lanka, and in Argentina and Chile.

Irish gauge, 1,600 mm (5 ft 3 in), runs in daily service in Ireland and also in two Australian states, Victoria and South Australia, and three Brazilian ones: Rio de Janeiro, São Paulo and Minas Gerais.
Russian gauge, 1,520 mm, is the dominant track gauge across the countries of the former Soviet Union.
Among the narrow gauges, 3 ft 6 in (1,067 mm) is the most widespread. It is the main gauge in South Africa and in the Australian state of Queensland, and it is the gauge of Japan's conventional lines, while the Shinkansen runs on standard gauge.
Standard vs broad vs narrow: cost, curves, speed
Gauge choice usually comes down to cost against speed and capacity.

Narrower gauges usually cost less to build, because they can use smaller cars and locomotives, which means a smaller loading gauge, and smaller bridges and tunnels, meaning a smaller structure gauge too. Narrow-gauge railways can also be less costly to equip and operate day to day than standard- or broad-gauge lines, not just cheaper to build in the first place. Lower-cost narrow-gauge lines are especially common in mountainous terrain, where the engineering savings on earthworks and structures can be substantial. The 2 ft (610 mm) Darjeeling Himalayan Railway in India is a well-known example, and the metre-gauge Glacier Express in the Swiss Alps is another. In Wales, the Ffestiniog Railway runs on a gauge of 1 ft 11½ in (597 mm).
In exchange for that lower cost, broader gauges offer higher speed and capacity than narrower ones. Narrow-gauge railways do allow sharper curves, but that same sharpness limits how fast a train can safely take them. Narrow gauge is not automatically slow, though: the 3 ft 6 in (1,067 mm) narrow-gauge speed record, 245 km/h (152 mph), was set in South Africa in 1978.
| Gauge type | Typical cost | Curves | Speed and capacity | Examples |
|---|---|---|---|---|
| Broad (Indian 1,676 mm, Irish 1,600 mm, Russian 1,520 mm) | Higher: larger loading and structure gauge needed | Needs gentler curves than narrow gauge | Higher speed and capacity | India, Pakistan, Bangladesh, Sri Lanka, Argentina, Chile, former Soviet Union, Ireland, Victoria, South Australia |
| Standard (1,435 mm) | Middle | Middle | Used by most high-speed lines | Most of Europe, North America, China |
| Narrow (under 1,435 mm, e.g. 1,067 mm) | Lower: smaller cars, locomotives, bridges and tunnels | Allows sharper curves, which limits safe speed | Record 245 km/h in South Africa (1978), 210 km/h in Queensland | Mountainous lines, 3 ft 6 in and other narrow gauges |
Britain's Gauge War: Brunel's broad gauge against standard gauge
Isambard Kingdom Brunel built the Great Western Railway to his own broad gauge of 7 feet between the rails, because he believed the extra width would give passengers and freight extra speed and comfort, according to Science Museum Group archives.
The result was that the Great Western Railway ran on 7 ft ¼ in broad gauge while its competitors ran on 4 ft 8½ in standard gauge, a split that came to be known as the British Gauge War. Trains, wagons and infrastructure built for one gauge could not run on the other, which made any point where the two systems met a serious operational headache.
Parliament stepped in with the Railway Regulation (Gauge) Act of 1846: any new broad-gauge line had to be built to seven feet, and new broad-gauge construction was confined to southwest England and Wales. Despite that restriction, broad gauge stayed in everyday, common use across the West of England for several more decades after the Act passed. Railway companies did eventually stop laying new broad-gauge track altogether, with no new mileage added after about 1860.
The GWR's own broad-gauge network did not disappear until much later. From around 1868, chairman Sir Daniel Gooch led a conversion of the entire system over to standard gauge, a project not completed until 23 May 1892. Network Rail tells the story of that final conversion.

America's twenty gauges and the scramble to standardize
Before the country standardized, American railroads were built to gauges ranging all the way from 2 ft to 6 ft, with no single national rule to tie them together. By the 1870s, that patchwork had grown to more than twenty different railway gauges in simultaneous use across the country.
The problem was especially pronounced in the South, which alone had built over 7,000 miles of five-foot gauge track by 1861.

When Congress funded the first transcontinental railroad, it settled the gauge question for that route: the Pacific Railroad Acts of 1863 specified that standard gauge be used. Both the Central Pacific and the Union Pacific laid their rails to the 4 ft 8½ in gauge as they built toward each other, a route covered in more detail in our article on the transcontinental railroad.
The rest of the country, and especially the South, still had to catch up. The Louisville & Nashville Railroad converted 2,000 miles of its own track to standard gauge in a single day, using a workforce of 8,000 people. The conversion effort kept spreading from there: by June 2, 1886, an estimated 14,000 miles of Southern track had been switched over to standard gauge, with another 2,000 miles of branch lines finished by the end of that same week.
Break of gauge: what happens where two gauges meet
A break of gauge is the point where lines built to different gauges meet. Trains cannot run through it, so goods have to be moved from one train to another, at first by hand and later by crane.
One of the earliest and most notorious examples was the break of gauge at Gloucester in 1843, where Brunel's broad gauge met standard gauge and became infamous for the chaos of transshipping goods between the two. The first break of gauge between Russian gauge and standard gauge was built in 1861, as dual-gauge track laid between the two border stations.
In 1848, Earl Grey, the Secretary of State for the Colonies in London, advised New South Wales Governor Charles Fitzroy that the Australian colonies should adopt one uniform gauge, the British standard 4 ft 8½ in. That advice was not followed everywhere: Victoria and South Australia both ended up building to Irish gauge instead, and standard-gauge track did not reach south from the New South Wales border to South Brisbane until 1930. Those completion dates are recorded by the University of Melbourne's engineering heritage archive.
The practical cost of that mismatch lingered for decades. It took a standard-gauge line between Albury and Melbourne, opened in 1962, to end most of the transshipment at Albury, long one of the most famous break-of-gauge stations anywhere.
Modern break-of-gauge crossings can still move freight quickly when the infrastructure is built for it. At the China-Kazakhstan border crossing at Khorgos, gantry cranes transfer shipping containers between trains of different gauge in as little as 47 minutes.

Rails & Rivals, our game on Steam, is a turn-based railroad strategy board game for 2 to 6 players: each player runs a rail company, lays track across a hex map and carries goods between cities, and the wealthiest company wins. The how to play page has the rules.
Keep reading
Sources
- Track gauge (Wikipedia)
- Broad-gauge railway (Wikipedia)
- Narrow-gauge railway (Wikipedia)
- Brunel's Broad Gauge Railway (Didcot Railway Centre / Great Western Society)
- Archive record relating to Brunel/GWR broad gauge (Science Museum Group Archives)
- British Gauge War (Wikipedia)
- Railway Regulation (Gauge) Act 1846 (Wikipedia)
- Why the end of the gauge war didn't standardise Britain's railway (Network Rail)
- Track gauge in the United States (Wikipedia)
- The Transcontinental Railroad: Rail Gauge (Linda Hall Library)
- Break of gauge (Wikipedia)
- Rail gauge in Australia (Wikipedia)
- Technology in Australia 1788-1988 - rail gauge standardisation (University of Melbourne (Australian Science & Technology Heritage Centre))